greenTEG AG: Researchers from the Guilin University of Technology and the Michigan Technological University used greenTEG’s gSKIN®-XP heat flux sensors to show how lowering the emissivity at the underside of concrete roof tiles can...
greenTEG AG: Researchers from the University of California used greenTEG’s gSKIN®-XI Heat Flux Sensor to investigate the thermal properties of a simple and cost-efficient installation approach of low-emissivity (low-e) films on windows....
Texys: Introducing the Texense YAW Pitot sensor with remote tube combining static, differential, yaw angle & board temperature in a compact lightweight housing. Sensor & tube packaged separately to aid Installation, High accuracy ±...
Texys: New for 2019, the Texense YAW Pitot V3 Sensor. A unique very high accuracy pitot sensor which provides absolute static pressure, air temperature and YAW angle measurements. Packaged into a single compact housing, light-weight and extremely...
Balluff is expanding their range of sensors for media-contacting temperature detection, in hydraulic power units for example. New are a temperature sensor with display, a temperature transmitter as well as a PT1000 sensor .The version without...
Variohm EuroSensor: Force Engineering, based in Shepshed near Loughborough, develops and manufactures customised Linear Induction Motor (LIM) based motion systems, serving a wide base of industries with applications as diverse as...
greenTEG AG: Researchers used greenTEG’s heat flux sensors to thermally characterize a geopolymer concrete containing phase change material (PCM). The PCM containing cube showed improvement in thermal performance compared to the reference....
E+E Elektronik: The temperature sensors of the Austrian sensor manufacturer E+E Elektronik are now available with RS485 interface. The Modbus RTU and BACnet MS/TP protocols facilitate the integration into a bus system. The installation-friendly,...
Exergen Global: Non-contact thermal sensors are remarkably diverse devices that can help ensure higher process speeds, more precise accuracies, tighter tolerances, and higher yields for a wide spectrum of manufacturing processes, including...
greenTEG AG: This brief case study presents the challenges of performing a U-value measurement on a roof and the precautions and steps to overcome them. The challenges of measuring a very low Uvalue and the corresponding measurement quality...
InfraTec GmbH: Pyroelectric detectors are ideally suited for gas analysis. Until now, this has been complicated if many gases should be measured. There were often simply too few measuring channels for this purpose. The new LRM-278 from InfraTec...
Heitronics: Infrared radiation thermometers measure the gas temperature in combustion processes quickly and reliably. The sighting depth of the device depends on the process conditions and the selected wavelength. Heitronics has developed an...
Exergen Global announced the industry’s only non-contact thermal dynamic management solution to combine a proprietary-design cooling mechanism with a unique emissivity control device to provide accurate, repeatable thermal measurement...
E+E Elektronik: The EE850 duct mount sensor from E+E Elektronik combines the CO2, relative humidity (RH) and temperature (T) measurement in a single device. The sensor can be easily integrated into a bus system via the RS485 interface (Modbus RTU...
Balluff is expanding their range of sensors for media-contacting temperature detection, in hydraulic power units for example. New are a temperature sensor with display, a temperature transmitter as well as a PT1000 sensor .The version without...
Exergen Global: Challenge: A large electric air heating solutions company needed a very fast thermal management solution to prevent overheating of the air heater element used in its flanged inline heaters. The heaters are employed in industrial...
E+E Elektronik: The high-end EE310 and EE360 industrial transmitters from E+E Elektronik are now available with stainless steel or with polycarbonate enclosure. The EE310 humidity and temperature transmitter is dedicated for demanding industrial...
greenTEG AG: The European Union’s Horizon 2020 Program is the largest research and innovation funding program ever launched to support scientific progress. Under this program, the EU granted greenTEG phase 1 funding of 50’000€ to...
greenTEG AG: Congratulations to Simon Caron, Marc Röger and Johannes Pernpeintner from the German Aerospace Center’s Institute of Solar Research for their recent publication “Heat Flux and Temperature Measurements on Glass...
greenTEG AG: In a study performed by students at East Bavarian Technical University, the measurement quality of U-values measured with a Temperature Based Method (TBM) versus a Heat Flux Based Method (HFBM) were compared. It was found that the...
WIKA has further developed its standard bimetal thermometers for global application in the process industry. The model TG53 conforms to the ASME B40.200 standard and is manufactured for the inch unit of measure. The model TG54 has been qualified...
Exergen Global announced that its Micro IRt/c-HB infrared non-contact sensors are being used to measure blood product temperatures in the ThermaCor® 1200 Rapid Thermal Infuser designed and developed by Smisson-Cartledge Biomedical, LLC and...
greenTEG AG: Start your temperature and heat flux measurements straight out of the box with the gSKIN® XO-Temp sensor & MultiLog datalogger package. Quick & Easy Setup. No hassle with calibration, soldering wires or incompatible data...
Baumer: With the new generation of universal temperature transmitters, FlexTop 2212 and 2222, Baumer is expanding its proven range of products. With integrated micro-USB port, automated cable compensation and a fast sampling time of less than 50...
greenTEG AG: We will exhibit our solution for continuous, non-invasive core body temperature measurements for wearable and med-tech applications at the Websummit in Lisbon. Contact us for a meeting during the fair. The core body temperature (CBT)...
E+E Elektronik: The EE23 industrial transmitters from E+E Elektronik measure relative humidity and temperature and also calculate the dew point and frost point temperature. The new model EE23-T5 is suitable for a temperature range of -40 °C to...
Exergen Global introduced the D501LN, a handheld certified infrared scanner that provides all the features found in Exergen’s DX501, with an extended nosepiece to enhance safety and ease-of-use. The length of the nosepiece in the D501LN...
greenTEG AG: Currently, there is a strong research effort of developing ‘smart’ building materials that respond to temperature changes in a way that improves building energy efficiency. One such method involves introducing Phase Change...
AMSYS: The HTU(F) 3833 and HTU(F) 3835 from the HTU383X series are ready-to-use digital plug and play modules for accurate humidity and temperature measurement with 3 V and 5 V supply. Power consumption during the measurement is typ. 450 μA....
E+E Elektronik: The duct mount EE850 from E+E Elektronik measures CO2 concentration up to 10000 ppm (1 %), as well as relative humidity (RH) and temperature (T). It is ideal for demand controlled ventilation, building automation and also for...
